DIGITAL SURFACE PROFILE GAUGE (TQC, NETH.)

Digital Surface Profile acc. 0.002mm Range : 0-1000 microns 
Acc. ±1 microns for checking sand blasting, shot blasting &grit blasting surface

DIAL SURFACE PROFILE GAUGE

Surface Profile Gauge Indian Make

Dial type Gauge with accuracy of .002 mm for checking height of peak & depths of valley & measuring the surface finish in micron directly. Range 0-1000 Microns. It is a dial gauge mounted on large base foot in the centre of which is a precision-ground tungsten carbide tip. Accry 2 Microns.  

PIN HOLE DETECTORS

Indian made pinhole detector for checking any pinhole or defects on paint coated surface. with Sponge Prob
Range : 0-300 microns & 9 Volts
Pinhole Detector Heavy Duty 0-500 microns and Digital Range : 9,6.7 & 90 Volts. Combine

HOLIDAY DETECTOR U.K./ U.S.A.

Battery operated with voltage output of 0-15 KV & 0-30 KV. checks Bitumen or Epoxy on concrete eg. Storage tanks, water and sewage treatment facilities. Testing insulating coating on oil, gas & water pipelines. Provided rechargeable battery earth lead, high voltage probe, handle & lead band brush probe.

TESTEX TAPES USA

Elcometer U.K. 122 Testex Tapes provides a quick, easy to use low cost method of measuring rough surface profiles after shot or grit blasting. Used in conjuction with the tape gives peak to valley height. This method enables a replica of the anchor pattern profile to be produced, which can then be attached to a report, to provide a permanent record for future reference. Set of 50 replicas per roll.
Ranges Coarse E122...B Coarse 50 Microns, and X Coarse 37-100 microns Model E-122. Foil Thickness Gauge 1 micron Accuracy . For checking thickness of impressions for above.

TESTEX GAUGE FOR PRESS-O-FILM

Acc. of 0.01mm , Range 0 to 10mm, Acc. 0.01mm for checking diameter thickness of small components and checking the thickness of sheets, papers, cardboards on any type of flat sheets.

DIGITAL THERMOMETER

For checking temperature 0-1000º C with standard Probe.
for checking surface temperature. Also available thermemeter from -60 to 1200ºC The Digital Thermometer are Available long needle probes for checking Temperature liquids or Air

SWEDISH STANDARD BOOK (SWEDEN)

With various chart, colored actual photos & plates of rust checking & surface finish of Shot Blasting Sweden as per DIN Standard, ASTMBS Standard, ISO 8501-1-1988 & SS 055900. Finishes of surfaces checking SA2,2.5 & 3. SSPC - VIS - 1 Visual standards for Abrasive blast cleaning surfaces USA SSPC - VIS - 3 Visual standards for powder & Hand Tool cleaning steel. USA

WET FILM THICKNESS COMB USA MAKE

Range : 25 to 2032 Microns Scale on all 4sides of gauge of Aluminum. Wet film comb USA Stainless Steel Range 25 to 3000 Microns

BRESLE - KIT CHLORIDE TEST KIT (USA / TQC, NETH.)

The Bresle KIT - Chloride Test Kit includes all the necessary equipment for assessing the level of soluble salts on blast-cleaned surfaces prior to coating. Inside the Bresle KIT - Chloride Test Kit is a conductivity gauge used for the assessment of soluble salt ions as chlorides, sulphates and nitrates. The Bresle Method described in the ISO 8502-6 and ISO 8502-9 standard, states that the conductivity is mainly directly proportional to the concentration of dissolved chloride ions in the solution.

HYPERDEMIC NEEDLE PRESSURE

Hyperdemic Needle Pressure Gauge USA make pocket size to 
determine blast cleaning air pressure at the nozzle. Instant 
reading from 0-160 Psig. 
Accuracy + 5%.

CLEMXEX PRESSURE BLAST ANALYER

USA make portable hand held for measuring the orifice in inches & air consumption 
( CFM @ 100 PSI) of an abrasive blasting nozzle.

CROSS CUT ADHESION TEST KIT

FLASH MAGNIFIER

SURFACE COMPARATOR

SURFACE ROUGHNESS COMPARATOR

Surface Comparator – USA Make  

allows the estimation of the surface roughness by both touch & sight in accordance 

with ASTM D2217N method A and ISO8503 

for Grit Blasting / Shot Blasting.

DUST TEST KIT TQC NETHERLAND

MAGNETIC THERMOMETER